tdc_cpci500 series.b01 page 1 of 4 technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 www.murata-ps.com cpci500 series 500w 6ux4hp dc/dc compactpci? power supply $ for full details go to www.murata-ps.com/rohs features 6ux4hp package 500w power at 0-50oc picmg 2.11 compliant rohs compliant widerange 36-72vdc input range ipmi option active or passive current sharing 47-pin i/o connector 80% ef?ciency no minimum load hot-swap capable description the cpci500 is a high-reliability, 500w, 6ux4hp compactpci? power supply operating from wide- range dc-input. the use of our patented v-series topology yields high ef?ciency which consequently permits packaging of this product in a compact, single card slot format (4hp). oring diodes and current sharing allow the cpci500 to be operated in n+n parallel-redundant con?gurations. available with an ipmi interface option, the cpci500 was designed for hot-swap, redundant con?gurations to support high-availability (ha) telecom applications. with a widerange input of 36-72vdc, safety agency approvals to ul60950 and en60950, emi compliance to etsi and telcordia standards, the cpci500 was designed with globally-deployed systems in mind. additional features include remote sense compensation, unit enable control (en#), output inhibit control (inh#), output fault signal (fal#), and thermal warning signal (deg#). leds are provided for visual indication of input power presence and output fault condition. the 4hp package and complement of global safety agency approvals provide for an advanced, high-density, high-ef?ciency power solution for your compactpci requirements. input characteristics parameter conditions min typ max units input operating voltage 36 72 vdc input voltage withstand 34 75 vdc inrush current 36vdc input 25 apk 72vdc input 50 apk output characteristics output nominal voltage output current total regulation 1 min max a max b v1 +5.0vdc 0a 55a 30a 1% v2 +3.3vdc 0a 30a 60a 1% v3 +12vdc 0a 11a 11a 1% v4 -12vdc 0a 1.7a 1.7a 3% parameter conditions min typ max units temperature coef?cient 0.02 %/oc pard (v1 & v2) 20mhz bandwidth 50 mv p-p pard (v3 & v4) 20mhz bandwidth 120 180 mv p-p output power 50oc, 400lfm air?ow 0 500 w output power 70oc, 400lfm air?ow 0 250 w transient response v, 50% load step 8 %vnom settling time 200 sec over-voltage protection all outputs 125 135 %vnom minimum load 0 a output holdup tim full load, low line 12 16 msec remote sense compensation v1, v2 & v3 300 mv current share tolerance v1-v3; full load 10 % isolation pri-sec 4 kvac pri-chassis 1.5 kvac sec-chassis 500 vac notes: 1 total regulation includes line, load, and cross regulation. selection guide model number power output current ipmi ish1 5v 3.3v 12v -12v cpci500d-1 500w 55a y 11a 1.7a n p no cpci500d-2 500w 30a n 11a 1.7a n p no cpci500d-3 500w 30a n 11a 1.7a y a no cpci500d-4 500w 55a y 11a 1.7a y a no cpci500d-5 500w 55a n 11a 1.7a n a no cpci500d-6 500w 30a n 11a 1.7a n a no cpci500d-1c 500w 55a y 11a 1.7a n p yes CPCI500D-2C 500w 30a n 11a 1.7a n p yes cpci500d-3c 500w 30a n 11a 1.7a y a yes cpci500d-4c 500w 55a y 11a 1.7a y a yes cpci500d-5c 500w 55a n 11a 1.7a n a yes cpci500d-6c 500w 30a n 11a 1.7a n a yes c nput ran g e e nt s h ar i ng s c c c c c c c c c c c c c c c c c c c c
tdc_cpci500 series.b01 page 2 of 4 technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 www.murata-ps.com cpci500 series 500w 6ux4hp dc/dc compactpci? power supply protection parameter conditions/response inception min typ max units thermal shutdown automatic recovery upon restoration to operational temperatures 90 oc output power limit automatic recovery 530 w input protection internal line fuse, littlefuse bln 25p rohs or equivalent 25 a over-voltage protection output v1, latching 6.0 6.5 7.0 vdc output v2, latching 3.9 4.3 4.7 vdc parameter conditions/response output overload protection outputs are individually protected against overloads and inde?nite short circuit with automatic recov ery upon removal of the fault condition. hot-swap capability design veri?cation testing (dvt) con?rms that voltage excursions on the output buses resulting from insertion/extraction events do not exceed the speci?ed maximum of 5%. however, routing of power and signal lines in the mating backplane is critical to minimization of such excursions. in addition, performance can be critically affected by load characteristics including resistance, negative resistance, and reactiv e components. while the control loop responses have been designed for optimum hot-swap performance over a wide range of characteristics, there may be instances where the voltage excursions exceed published speci?cations. in such cases, the control loop responses can be modi?ed to perfo rm optimally. output fault isolation output isolation devices are present in all outputs to isolate faults within a failed power supply. status & control signals & indicators name description hot-swap enable short pin on connector will enable the outputs when the mating pin is tied to dc grd. supply will not power up until this pin is engaged to its mate in the backplane. unit output will be inhibited as pin is disengaged from the mating connector. output inhibit secondary referenced; active low, ttl compatible. logic 0 or short circuit to logic rtn (pin 40 or 43) inhibit s all outputs. dc good secondary referenced. open collector signal with an internal 2.2k pull-up resistor is connected to the +5v output. ttl signal will transition high when all outputs are between 90% and 110% of their nominal voltage. remote sense connection of the sense leads across the load at the desired point of regulation will compensate for voltage distribution drops up to 700mv between the output terminals of the power supply and the point of connection. the unit reverts to local sensing if the sense l ines are opened for any reason. the output is protected against shorted or open leads. applies to all outputs. fan alarm secondary referenced; ttl compatible; active low. signal transitions to a logic 0 denotes a thermal warning. power present indicator led a green led will be illuminated when the input voltage is present and above the minimum requirement. dc good indicator led a green led will be illuminated when the output voltages are within 90-110% of speci?cation, coincident with assertion of the d c good signal. this led will be extinguished if any of the output voltages is outside of this range. fan good indicator led a green led will be illuminated when the fan is operational, coincident with de-assertion of the fan alarm signal. this led wi ll be extinguished in the event of a fan failure. sync start a power supply generated signal used to simultaneously start power supplies connected in parallel when the load on any output e xceeds a single power supplys capacity for that output. these pins must be bused together at the backplane in parallel/redundant applications (n+n) when n>1. in simple redundant (1+1) or non-parallel applications (1+0), the pin can be ignored. power supply present this pin presents a dc ground signal to the mating pin in the backplane. it is intended to be used by the system to detect the presence of a power supply when the supply is mated into an available position. environmental characteristics parameter conditions min typ max units ambientoperatingtemperature de-rate output power linearly above 40oc to 250w at 60oc. 0 60 oc ambient storage temperature -25 +125 oc humidity operating; non-condensing 10 95 % storage; non-condensing 5 95 % altitude operating. de-rate ambient temperature by 2co per 1000ft above 5000ft. -200 10000 ft storage -200 40000 ft cooling self-cooled by internal fan general characteristics parameter conditions min typ max units ef?ciency 48vdc input, 500w load (dependent upon load pro?le) 65 % switching frequency 72 khz mtbf calculated per mil-hdbk-217f, 25oc, ground benign 84 khrs weight unpackaged 3.6 kg
tdc_cpci500 series.b01 page 3 of 4 technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 www.murata-ps.com cpci500 series 500w 6ux4hp dc/dc compactpci? power supply mechanical dimensions certifications agency/characteristic standard ul ul1950 csa csa950 (per cul) vde en60950 ce lvd directive; self-certi?ed rohs en directive 2002/95/ec; self-certi?ed; see selection guide table for speci?c model compliance selv self-certi?ed vibration mil-std-810f, method 514.5, procedure i; self-certi?ed shock mil-std-810f, method 516.5, procedure i; self-certi?ed electromagnetic compatability (emc) conducted emissions en 300 386, nebs gr-1089 electrostatic discharge (esd) en61000-4-2, level 3, criteria b radiated immunity en61000-4-3, level 3, criteria a conducted immunity en61000-4-4, level 3, criteria a line voltage surge en61000-4-5, class 3, criteria b
tdc_cpci500 series.b01 page 4 of 4 technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 www.murata-ps.com cpci500 series 500w 6ux4hp dc/dc compactpci? power supply murata power solutions, inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. the descriptions contained her ein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. speci?cations are subject to chan ge without notice. ? 2008 murata power solutions, inc. usa: mans?eld (ma), tel: (508) 339-3000, email: sales@murata-ps.com canada: toronto, tel: (866) 740-1232, email: toronto@murata-ps.com uk: milton keynes, tel: +44 (0)1908 615232, email: mk@murata-ps.com france: montigny le bretonneux, tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com germany: mnchen, tel: +49 (0)89-544334-0, email: munich@murata-ps.com japan: tokyo, tel: 3-3779-1031, email: sales_tokyo@murata-ps.com osaka, tel: 6-6354-2025, email: sales_osaka@murata-ps.com website: www.murata-ps.jp china: shanghai, tel: +86 215 027 3678, email: shanghai@murata-ps.com guangzhou, tel: +86 208 221 8066, email: guangzhou@murata-ps.com murata power solutions, inc. 11 cabot boulevard, mans?eld, ma 02048-1151 u.s.a. tel: (508) 339-3000 (800) 233-2765 fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com iso 9001 registered safety agency ratings input voltage 36-72vdc input current 25-12.5adc input power 620w notes: (1) pin numbers correspond to the female backplane connector. (2) l = long length pin (first make, last break); m = medium length pins; s = short length pins (last make, first break) mechanical shock: mil-std-810d, method 516.3, procedure 1. vibration: mil-std-810d, method 514.3, procedure 1. dimensions: 6u x 4hp x 160mm (see mechanical above) emc & safety emi: nebs compliant, etsi compliant safety agency ratings input voltage: 48 vdc input current: 15a input power: 620w agency approvals ul1950/csa950, en60950, ce mark. (low voltage directive) connector pin # 1 staging 2 signal name description 1-4 m v1 v1 output 5-12 m rtn v1 and v2 return 13-18 m v2 v2 output 19 m rtn v3 return 20 m v3 v3 output 21 m v4 v4 output 22 m rtn signal return 23 m reserved reserved 24 m rtn v4 return 25 m ga0 geographic address bit 0 26 m reserved reserved 27 s en# enable 28 m ga1 geographic address bit 1 29 m v1adj v1 adjust 30 m v1 sense v1 remote sense 31 m ga2 geographic address bit 2 32 m v2adj v2 adjust 33 m v2 sense v2 remote sense 34 m s rtn sense return 35 m v1 share v1 current share 36 m v3 sense v3 remote sense 37 m ipmb scl ipmb serial clock line 38 m deg# degrade signal 39 m inh# inhibit 40 m ipmb sda ipmb serial data line 41 m v2 share v2 current share 42 m fal# fail signal 43 m ipmb pwr ipmb power input 44 m v3 share v3 current share 45 l cgnd chassis grnd (safety grnd) 46 m acn/+dc in ac input neutral/+dc input 47 m acl/-dc in ac input line/-dc input complies with ipmi v1.5 rev 1.1 and ipmb v1.0 complies to picmg2.9 (compactpci systems management speci?cation) 8 analog inputs con?gured for monitoring voltages and currents on power supply outputs v1 - v4 monitors the state of the thermal sensor output inhibit control can be overwritten by ipmi commands self test with led indicator (can be read and overwritten by ipmi commands) 6 programmable thresholds on each analog sensor each threshold on each sensor can be enabled to generate event messages if that threshold is crossed thermal sensor can be enabled to generate event messages responds to all mandatory ipmi commands and numerous optional commands as indicated in the functional speci?cation firmware can be upgraded via the ipmb bus includes device sdrs (sensor data records) - these specify the type of sensor for each input (voltage, current, temperature, etc.) as well as the conversion formulas from raw adc data to voltages, currents, etc. includes fru type information such as model number, serial number and ?rmware creation date ipmi/ipmb power supply satellite controller features package specifications 05/14/08
|
